How To Install Carport Mounting System Effectively?
Dec 16, 2021
Product Details
Serial No. | Definition | Picture | Material/Dimension | Remarks |
1 | HPX-DCY-35 |
| AL 6005-T5 /SUS304 | Tool: M8 Inner Hexagon Spanner |
2 | HPX-DZY-35 |
| AL 6005-T5 /SUS304 | Tool: M8 Inner Hexagon Spanner |
3 | HPX-CCC |
| AL 6005-T5 /SUS304 | Tool: Electric Drill+ Socket Wrench+ Electric Source |
4 | HPX-HPYK |
| AL 6005-T5 /SUS304 | Tool: M8 Inner Hexagon Spanner |
5 | HPX-HCR |
| AL 6005-T5 |
6. | HPX-CYZZJ-1 |
| AL 6005-T5 /SUS304 | |
6. | HPX-CYZZJ-2 |
| AL 6005-T5 /SUS304 | |
6-1 | Front Rod |
| AL 6005-T5 |
Tool: M12 Outer Hexagon Spanner (Please assemble according to below Installation Steps)
|
6-2 | Side bar |
| AL 6005-T5 | |
6-3 | Side bar |
| AL 6005-T5 | |
6-4 | Back bar |
| AL 6005-T5 |
6-5 | Base |
| AL 6005-T5 | |
6-6 | Corrugated Plate |
| AL 6005-T5 | |
6-7 | Girder |
| AL 6005-T5 | |
6-8 | Bolt |
| M12*130 SUS304 | |
6-9 | Bolt |
| M12*110 SUS304 |
|
|
|
|
2、Installation Steps
2.1 Support Installation
Please note that ① and ② of the beam is not the same, please choose the correct girder
3、Carport installation:
3-1 Support Installation
Please pay attention to the installation, please ensure that the "L1" is consistent with the drawing data.
3-2 Crossbeam installation:
Please pay attention to the installation, please ensure that the dimensions "L2" and "L3" are consistent with the drawing;If the beam needs splicing, please make Install with st6.3-25 tapping screw (as shown).
3-3Solar Panels Installation
Lay the solar panel on the rail in turn, and lock it with end and middle clamps. Follow L4 and L5 in the drawing. The control distance between the panels is 20mm.
4th. Notice:
This installation is only applicable on our this product. Unless there is no other way, please install strictly according to our providing install steps. Contact us if there is any changes of installation steps.
1. For your safety please strictly comply with the operating procedures of the use of tools.
2. Please do the necessary protective measures as power source is using under installation
3. Product section is relatively sharp, please wear labor protection appliance to avoid your unnecessary injury.
4. In the construction of a number of people, please make instant communication to avoid accidental injury.
5th, Tools Preparing
Serial No. | Tools Name | Purpose |
1 | M8 Inner Hexagon Spanner | Using during installation of side pressing block, middle pressing block and Horizontal pressing block |
2 | M12 Hexagon Spanner, Socket Wrench | Using during installation of Support( M12*110/M12*130) |
3 | Manual Electric Switch, Socket Wrench, Electricity | Using during under installation of Cross Beam Linking(ST6.3*25) |
4 | Gloves, Safety hat, Protective eyewear, Safe Belt, Safety Footwear, Insulated Gloves and other necessary Safety Products. |
If there is any confusion during installation, please contact me at mina@grengysolar.com .
